Archive for January, 2012

« Older Entries

Newcastle Heating Installation Tip: Why AFUE Ratings Matter When Buying a New Furnace

Monday, January 30th, 2012

When you are in the market for a new furnace for your Newcastle home, there are several reasons you should pay attention to the annual fuel utilization efficiency (AFUE) rating. All newer model furnaces get an AFUE percentage, which measures how much fuel a particular model converts into heat. Furnaces with higher AFUE ratings are more efficient, but the size and type of furnace will also factor into how much you’ll save on energy costs.

Understanding the AFUE Ratio

The minimum AFUE rating for new furnaces is 78%. This means that seventy-eight percent of the fuel is turned into heat, and the remaining percentage is lost either through poor insulation, air leaks, or the ventilation system in the home. Because there’s no heat loss through a chimney flue, some all-electric furnaces can have an AFUE rating as high as 98%. However, if the cost of electricity used to meet your normal heating needs is higher than the efficiency savings, you may want to consider other options. Talk to a qualified HVAC contractor for advice about the most cost-efficient heater for your home.

Furnace Efficiency Features

Furnaces manufactured 15-20 years ago have significantly lower AFUE ratings (between 55%-70% for most older models) because they are typically single-stage, or single-speed systems. Single-stage furnaces are less efficient because they are designed to cycle on at full capacity and shut off when the desired temperature is met.  Newer, two-speed models have a second setting that runs consistently at a lower speed, which saves energy by burning less fuel. Multispeed furnaces that have variable-speed blowers are the most efficient because they operate at various levels and automatically adjust to the thermostat to maintain a constant temperature.

If you look at the AFUE ratings for multispeed and variable-speed furnaces, the ratios should be above 80%. Keep in mind that this only determines the efficiency levels for the furnace itself. You’ll need to factor in whether or not your home has proper insulation and other upgrades, such as double-paned windows and doors.

Call Advantage Airtech Ltd. to speak with one of our qualified HVAC technicians about a furnace upgrade for your Newcastle home.

Tags: , , , ,
Posted in Heating | Comments Off

North York Heating Contractor Guide: What is a Gas Furnace Draft Hood?

Friday, January 27th, 2012

As every North York HVAC contractor knows, a draft hood is a necessary part of any gas burning appliance. For a gas furnace in particular it ensures steady air flow to the burners to avoid flares or the pilot light being put out by fluctuation in temperature and air flow.

What the Draft Hood Does

The draft will change in the chimney as exhaust vents towards it – especially when going from cold air to hot. A draft hood is placed above the upper most part of the gas furnace to draw air into the chimney and makes it possible to draw more or less air through the chimney as necessary to create a constant flow.

This makes it possible for the burner to enjoy consistent air flow without any wind gusts or sudden temperature spikes or drops. Hot air, if not put through a draft hood would create a strong air flow through the burners.

A draft hood cools the air as it is released by the burners from 500 degrees F to between 300 degrees F and 350 degrees F. The cooling needs to be carefully calibrated to avoid condensation build up in the chimney however – a problem that occurs when the temperature gets too low.

Maintaining Pressure

The draft hood is a part of a larger system designed to maintain air flow to the chimney. For every cubic foot of gas burned, the furnace needs to have 15 cubic feet of air for combustion and another 15 cubic feet of air for dilution. A draft hood and the rest of the ventilation system make it possible to put a furnace that has many thousands of BTUs in the basement of your home and still supply it with enough air to burn gas and dilute the exhaust before it enters the chimney.

For all of these reasons, if you see your pilot light flickering irregularly, notice a backflow of exhaust or a burning smell in your North York home’s furnace room, it’s important to call a professional who can inspect and repair the problem before it becomes any worse. Not only can gas burner exhaust contain high levels of carbon monoxide, it can be bad for the device and the chimney if it doesn’t vent properly.

Tags: , , , ,
Posted in Heating | Comments Off

Unionville Heating Repair Question: What Does a Furnace Fan Limit Switch Do?

Wednesday, January 25th, 2012

When researching your Unionville home’s furnace and potential problems it might have, you’ve probably run across a few references to the fan limit switch. And while you know that it can break in a number of ways, do you know what the switch does and what you should look for when checking your furnace its air handler for problems?

What the Limit Switch Does

To put it very simply, the furnace fan limit switch is a control that tells your furnace’s fan when to turn on and off. So, when the furnace isn’t on, it tells the blower not to operate (and send cold air into your home) and when the furnace is on, it tells the blower to turn on and start circulating the warm air.

While the primary function of the limit switch is to turn the blower fan on and off, it also has a safety role. When the temperature in the air supply plenum gets too hot, the limit switch turns off the furnace boiler to keep there from being any damage from overheating. This is handy if there is a blockage in the air vents or the controls are messed up due to water damage or improper adjustments to the settings.

Looking for Problems

Most of the time, when there is an issue with your furnace turning off or on frequently, the limit switch is one of the first things you will check. Because the switch is electronic and is attached to a thermostat which measures temperature in the air supply plenum, a small problem can result in it not working properly. So, you can easily check it by temporarily bypassing the switch and seeing if your device turns on or off properly.

In many cases, if the limit switch is the problem, you will still need to call a professional for replacement, but you can avoid a lot of headaches related to tracking down the source of the problem. If you suspect a limit switch problem, make sure to call a Unionville heating and air conditioning contractor immediately, because it does provide an important safety function and because without it your furnace won’t cycle on and off properly.

Tags: , , , , , , ,
Posted in Heating | Comments Off

Time is Running Out to Win a $25 Gift Card to Tim Horton’s Coffee!

Tuesday, January 24th, 2012

If you haven’t “liked” our Facebook page yet, do so soon! You will be entered to win one of four $25 Gift Cards to Tim Horton’s Coffee, which is something that everyone needs this winter! Delicious coffee and pastries will help keep you warm during these cold months. The raffle ends on 1/31/2012, so don’t wait until it is too late.

If you “like” our page, you will get to receive news and updates about our company. You will also be the first to know about any special deals that we are offering! We provide a lot of home improvement and energy saving tips that are great for any homeowner to know. “Like” us today!

Here is the link to our Facebook page: http://www.facebook.com/pages/Advantage-Airtech-Ltd-Heating-and-Air-Conditioning/163060727059848

Offer expires 1/31/2012

Tags:
Posted in Promo | Comments Off

Blackstock Heating Guide: Basic Boiler Maintenance

Monday, January 23rd, 2012

The boiler in your Blackstock home is a sensitive piece of equipment that needs routine maintenance and repairs. Regularly maintaining your boiler is especially important for safety reasons. Many boiler malfunctions and accidents are due to neglecting some of these basic tasks.

Even if you’ve just installed a new boiler, the safety valves and settings should be checked by a professional on a regular basis to prevent a breakdown or hazard. We recommend that you schedule a boiler inspection and cleaning at least once a year. Call Advantage Airtech Ltd. if you have any questions about boiler maintenance.

A service technician will measure the pressure, drain and remove sediment buildup, test the efficiency ratings, and make sure your boiler is set at the right temperatures. Regular maintenance can also help you determine whether or not you need a boiler replacement. By keeping track of performance levels, you will be able to tell when it’s time for an upgrade.

Other tasks performed during an annual maintenance visit include cleaning and lubricating all the components, checking for any leaks or clogs, and testing gas boilers for any carbon monoxide intrusion. If you have any gas appliances in your home, you should always have carbon monoxide detectors and test them once a month.

Boiler pressure is something that you can check often on your own. If you aren’t sure how to read the pressure gauge, or if you aren’t sure what the right pressure should be, just call one of our technicians to walk you through this process.

Always call Advantage Airtech Ltd. if you have any problems with the boiler in your Blackstock home. We are here to help and answer any questions you may have.

Tags: , , , , , , , ,
Posted in Heating | Comments Off

Clarington Heating Installation Guide: Programmable Thermostats

Wednesday, January 18th, 2012

Programmable thermostats are one of the best ways to save on heating costs, especially if you have a hard time remembering to turn down the heat in your Clarington home. Installing a programmable thermostat will allow you to set the times you want the heat turned up or down. Not only will this make heating your home more consistent and save energy, but it will also allow you to tailor your heating needs to your schedule.

For instance, you can set the thermostat to turn on before you get up in the morning so that the house is already warm when you get out of bed, and conversely, set it to turn down after you go to bed or leave the house for work. Depending on the brand and setting options, programmable thermostats are relatively inexpensive and easy to install.

Although all styles are slightly different, here are some basic instructions that show you how easy it is to install a programmable thermostat.  Remember, this is only a general guide; always check the instructions inside the packaging of your new thermostat before you install it, or check with an electrician.

1. Remove the Old Thermostat

Before you remove the old thermostat, check to see where it’s mounted. If it’s mounted to an electrical box, the voltage used to power the old thermostat may not be compatible with the new one. Ask a certified electrician or Clarington heating technician if you aren’t sure.

CUT THE POWER TO THE HEATING SYSTEM TO AVOID ELECTRIC SHOCK. You should always turn off the main power supply to your heating system before installing any new thermostat. If you aren’t sure how to do this, ask your HVAC contractor. Once you unscrew the mounting plate for the old thermostat, just unhook the wires. Don’t throw an old mercury controlled thermostat. You should ask your local waste management facility how to properly dispose of mercury products.

2. Locate all Wires

Wrap the loose wires around a pencil to keep the wires from falling back into the wall. Identify and label each corresponding wire with a letter (do not use color coding since this is not always accurate). Strip the plastic off the ends of the wires about ¼ inch if you need to.

3. Install and Insulate Wallplate

If the area around the new wallplate is larger than the plate, insulate the hole with non-flammable insulation. Take the wallplate off the programmable thermostat and hold it against the wall to mark the screw holes with a pencil. Pull the wires through the large opening at the bottom and screw the plate to the wall.

4. Wiring

Make sure you are comfortable with wiring before you attempt to do any electrical installations. Check the manual for your programmable thermostat for instructions on wiring that specific model. In general, you’ll want to make sure you match the wire labels with the corresponding terminals on the thermostat. Sometimes there will be extra wires that aren’t needed. Always test it before completing the installation. Don’t forget the battery!

5. Install the Faceplate

Once you have it wired correctly, all you need to do is align the brackets on the faceplate with the corresponding slots on the wallplate and fasten the faceplate to the rest of the mounting. Lastly, tighten the screw at the bottom of the thermostat to hold it in place.

If you have any questions regarding programmable thermostats, give us a call.

Tags: , , , , , , ,
Posted in Heating | Comments Off

Sizing a Tankless Water Heater for Your Hayden Home

Monday, January 16th, 2012

Tankless water heaters are gaining popularity among Hayden homeowners because of their on demand hot water supply and space-saving design. Although they are more expensive than traditional tank water heaters, on demand water heaters are more efficient, reliable, and easier to install and maintain. Before choosing to install a tankless water heater, however, you will have to decide which size will meet your hot water needs.

Rather than storing hot water in a tank, the tankless models heat the water with individual units located near the application where hot water is needed, such as a shower or washing machine. For larger homes, some of these smaller units cannot heat enough water for several applications running at the same time. You can also install a single tankless water heater for the entire house, or separate ones for appliances that use more hot water.

Finding the proper size and type will depend on the flow rate—measured  by a GPM (gallons per minute) number—that each fixture needs. Every application has a standard flow rate that must be added up in order to calculate the hot water demands for your entire home. For instance, if someone is using a sink with a 1.5 GPM at the same time another person is running a shower with a 2.0 GPM, the flow rate for the tankless unit would need to be at least 3.5 gallons per minute. You will have to add up the flow rate for all the applications in the house to get the minimum GPM figure for your tankless water heater.

In addition to flow rates, tankless hot water heaters are also measured by how much the water temperature needs to rise as it moves through the heating unit. You can determine the temperature rise for each application by subtracting the temperature of water coming in from the desired temperature going out. Once you add those together with the overall flow rates, you will know which tankless water heater can handle your overall hot water needs.

Before you buy an on demand hot water heater, it is best to talk to a professional installer. While the flow rates and temperature rise for most household appliances are fairly standard, these numbers can vary because of several factors. Size is not the only factor to consider when shopping for a tankless water heater. Fuel type and efficiency should also be factored in to your purchase, which is another reason to talk to a professional.

If you aren’t sure what type or size of tankless water heater is right for your Hayden home, call Advantage Airtech Heating & Air Conditioning to speak with one of our professional installers. We are always glad to offer our expert advice so that you can meet all of your hot water needs in the most efficient way possible.

Tags: , , , ,
Posted in Water Heater | Comments Off

Oshawa Heating Tips: Basic Heating Safety

Friday, January 13th, 2012

While you should schedule a yearly maintenance visit with a qualified HVAC technician to check for any safety concerns, you can also reduce potential safety hazards in the heating system of your Oshawa home. Whether you have a furnace, heat pump, or boiler, you can substantially decrease the chances of dangerous situations with a few minor routine tasks.

If you have any questions about how to better maintain your heating system, give Advantage Airtech Ltd. a call to speak with one of our expert HVAC technicians. Here are a few guidelines to get you started.

Ventilation in Forced-air Systems:

  • Regularly vacuum and clean out your heating vents and fan blower.
  • Check the condition of your chimney and vent pipe to make sure that none of the parts are damaged or show signs of deterioration.
  • Test the thermostat occasionally to make sure your heating system is working at optimal levels. There could be a safety concern if your heater is not properly heating your home.

Heat Exchangers:

  • Heat exchangers should be inspected often to prevent carbon monoxide leaks. Check for any obvious issues, such as rust or other damages.
  • The heat exchanger for furnaces should be inspected by a professional once a year in case there are hidden problems with the equipment, or if any of the components need to be replaced.
  • Check the pilot light in gas furnaces for any flickers or changes in color. Have someone turn up the thermostat while you watch the light, but turn off the system for five minutes first. If there are any changes, there could be a problem with the heat exchanger. Call a professional if you suspect issues with your heat exchanger.

Heating Equipment Inspections and Adjustments:

  • Boilers should be drained regularly to reduce sediment buildup, in addition to testing the water level safety controls. It’s best to have a professional perform these tasks if you aren’t sure how to do them on your own.
  • Adjust the temperature settings if you suspect that the heater isn’t working properly, and if it doesn’t work call a professional heating technician, or if you aren’t sure how to locate or adjust the controls.
  • Check the overall equipment for cracks, rust, or any other obvious signs of damage or deterioration that could create safety hazards.

In addition to performing these tasks, call a licensed Oshawa heating contractor to inspect your heating system at least once a year.

Tags: , , , , , ,
Posted in Heating | Comments Off

Blackstock Heating Installation Guide: System Ventilation 101

Wednesday, January 11th, 2012

Maintaining Proper Ventilation for Combustion Systems

Anytime you maintain, retrofit, or replace a gas heating system in Blackstock you also need to be concerned with air quality. Combustion air is needed by all oil and gas heating systems to support the combustion process. This air is provided in some homes by unintentional air leaks, or by air ducts that connect to the outdoors. The combustion process creates several byproducts that are potentially hazardous to human health and can cause deterioration in your home. You can protect yourself from these hazards, as well as maintain energy efficiency, by ensuring that your chimney system functions properly and that your gas heating system is properly ventilated. In some cases, installing a sealed-combustion furnace or boiler can also help.

Chimneys

Properly functioning chimney systems will carry combustion byproducts out of the home. Therefore, chimney problems put you at risk of having these byproducts, such as carbon monoxide, spill into your home.

Most older gas furnaces and boilers have naturally drafting chimneys. The combustion gases exit the home through the chimney using only their buoyancy combined with the chimney’s height. Naturally drafting chimneys often have problems exhausting the combustion gases because of chimney blockage, wind or pressures inside the home that overcome the buoyancy of the gases.

Atmospheric, open-combustion furnaces and boilers, as well as fan-assisted furnaces and boilers, should be vented into masonry chimneys, metal double-wall chimneys, or another type of manufactured chimney. Masonry chimneys should have a fireclay, masonry liner or a retrofitted metal flue liner.

Many older chimneys have deteriorated liners or no liners at all and must be relined during furnace or boiler replacement. A chimney should be relined when any of the following changes are made to the combustion heating system:

When you replace an older furnace or boiler with a newer one that has an AFUE of 80% or more. These mid-efficiency appliances have a greater risk of depositing acidic condensation droplets in chimneys, and the chimneys must be prepared to handle this corrosive threat. The new chimney liner should be sized to accommodate both the new heating appliance and the combustion water heater by the installer.

When you replace an older furnace or boiler with a new 90+ AFUE appliance or a heat pump. In this case, the heating appliance will no longer vent into the old chimney, and the combustion water heater will now vent through an oversized chimney. This oversized chimney can lead to condensation and inadequate draft. The new chimney liner should be sized for the water heater alone, or the water heater in some cases can be vented directly through the wall.

Other Ventilation Concerns

Some fan-assisted, non-condensing furnaces and boilers, installed between 1987 and 1993, may be vented horizontally through high-temperature plastic vent pipe (not PVC pipe, which is safely used in condensing furnaces). This type of venting has been recalled and should be replaced by stainless steel vent pipe. If horizontal venting was used, an additional draft-inducing fan may be needed near the vent outlet to create adequate draft. Floor furnaces may have special venting problems because their vent connector exits the furnace close to the floor and may travel 10 to 30 feet before reaching a chimney. Check to see if this type of venting or the floor furnace itself needs replacement. If you smell gases, you have a venting problem that could affect your health. Contact your local utility or Blackstock heating contractor to have this venting problem repaired immediately.

Chimneys can be expensive to repair, and may help justify installing new heating equipment that won’t use the existing chimney.

Tags: , , , ,
Posted in Heating | Comments Off

Goodwood Heating Installation Tip: Pros and Cons of Various Heating Systems

Monday, January 9th, 2012

When it comes time to install a new heating system in your Goodwood home, there are a lot of options to consider. Many people get overwhelmed when confronted with all of the furnaces, boilers and heat pumps on the market these days. So, to help you get a handle on what each has to offer and which will offer you the best benefits, here is an overview of the modern heating system market.

Furnaces

Furnaces are the core of a forced air heating system and use gas, oil or electricity to heat air which is then circulated through your home by a blower in your air handler. Furnaces are among the most fuel efficient heating systems on the market today with options available at up to 95% AFUE (meaning it uses up to 95% of the fuel consumed to produce heat). They are also inexpensive to install and while they don’t last quite as long as boilers, they are highly efficient when well cared for.

Boilers

Boilers use gas, oil or electricity to heat water or steam which is then circulated through your home into radiators or baseboard heaters. The heated water or steam releases heat into your home and heats it in turn. While not quite as energy efficient as a high efficiency furnace, boiler heat is perfect for homes with existing radiators and no room for vents and ductwork. It also has less of an impact on indoor air quality since there is no air movement and boilers tend to last a very long time when well maintained.

Heat Pumps

Heat pumps are becoming increasingly popular, especially in milder climates where it rarely gets below 40 degrees F. A heat pump uses the same technology as an air conditioner to extract heat from outside using a compressor, evaporator coils, and condenser coils with refrigerant.

It is most efficient in the spring and fall when temperatures are mild, but it uses much less energy than either a boiler or furnace and it can be used in the summer to cool your home. When properly maintained, a heat pump will last 10-20 years and save quite a bit of money, though it is recommended that you have an emergency heat source for days when the temperature outside gets below 40 degrees F.

Tags: , , , , , , ,
Posted in Heat Pumps, Heating | Comments Off

« Older Entries