Posts Tagged ‘Hayden’

Bowmanville Heating Advice: Dangers of Not Changing Your Furnace Filter on Time

Monday, March 26th, 2012

Of the many ways to heat a home in Bowmanville, forced air systems are the simplest in function and the easiest to maintain.  They are so simple, in fact, it is easy to forget they need attention at all, but there are dangers to not changing your furnace filter on time that have a real and painful cost in efficiency and dollars.  Even health risks arise when filters have been neglected too long.

Contracting with a company like  Advantage Airtech ensures consistent maintenance and oversight to allow home owners the comfort and relaxation you deserve in your own home.

Back to Basics

Usually in the basement or a central location, a furnace heats air to a temperature set by the thermostat.  Over the years, technological improvements have enabled furnaces to be much smaller and fit into closets instead of the large and gangly monsters of old that could fill an entire basement.

By a fan in the furnace, the warm air is circulated through filters into a system of ducts to be distributed to grates in the wall or registers on the floor.  A second grate and duct system returns cooler air back to the furnace to be reheated.

Water can be added at the furnace to humidify the air and filters are able to remove some of the dust that typically floats invisibly throughout a home.

The Dangers of Not Changing the Filter

When the system is properly maintained, it is clean, efficient and produces comforting heat on demand at the touch of the thermostat or consistently throughout the day and night.

The furnace filter is designed to remove dust from air as it passes through your furnace. The longer your furnace filter is in place the dirtier it becomes. The increase of particles caught in the filter creates resistance to air flow through the filter and reduces efficiency.

To make up for the loss of flow through a dirty filter, the heat exchanger, usually a gas or oil fired flame, must work harder to produce the same amount of heat to the space.  This becomes costly financially and causes undo wear and stress on the equipment, requiring a partial or full replacement much sooner.

Additionally, operating above ideal designed conditions, cracks in the chamber may appear from the over load which can allow carbon monoxide, a toxic gas, to be released into the duct work.  This gas in large quantities in the home can cause headaches, nausea, and in extreme circumstances, even death.

Regular Maintenance

To avoid problems and excessive strain, remember to change the filters at the beginning of each new heating season.  An annual maintenance, check-up and thorough cleaning by a qualified company like  Advantage Airtech ensures a safe and comfortable season of warmth with no need to worry about the dangers of not changing filters in your Bowmanville furnace.

Tags: , , , , , , ,
Posted in Heating | Comments Off

Blackstock Heating Guide: Basic Boiler Maintenance

Monday, January 23rd, 2012

The boiler in your Blackstock home is a sensitive piece of equipment that needs routine maintenance and repairs. Regularly maintaining your boiler is especially important for safety reasons. Many boiler malfunctions and accidents are due to neglecting some of these basic tasks.

Even if you’ve just installed a new boiler, the safety valves and settings should be checked by a professional on a regular basis to prevent a breakdown or hazard. We recommend that you schedule a boiler inspection and cleaning at least once a year. Call Advantage Airtech Ltd. if you have any questions about boiler maintenance.

A service technician will measure the pressure, drain and remove sediment buildup, test the efficiency ratings, and make sure your boiler is set at the right temperatures. Regular maintenance can also help you determine whether or not you need a boiler replacement. By keeping track of performance levels, you will be able to tell when it’s time for an upgrade.

Other tasks performed during an annual maintenance visit include cleaning and lubricating all the components, checking for any leaks or clogs, and testing gas boilers for any carbon monoxide intrusion. If you have any gas appliances in your home, you should always have carbon monoxide detectors and test them once a month.

Boiler pressure is something that you can check often on your own. If you aren’t sure how to read the pressure gauge, or if you aren’t sure what the right pressure should be, just call one of our technicians to walk you through this process.

Always call Advantage Airtech Ltd. if you have any problems with the boiler in your Blackstock home. We are here to help and answer any questions you may have.

Tags: , , , , , , , ,
Posted in Heating | Comments Off

Sizing a Tankless Water Heater for Your Hayden Home

Monday, January 16th, 2012

Tankless water heaters are gaining popularity among Hayden homeowners because of their on demand hot water supply and space-saving design. Although they are more expensive than traditional tank water heaters, on demand water heaters are more efficient, reliable, and easier to install and maintain. Before choosing to install a tankless water heater, however, you will have to decide which size will meet your hot water needs.

Rather than storing hot water in a tank, the tankless models heat the water with individual units located near the application where hot water is needed, such as a shower or washing machine. For larger homes, some of these smaller units cannot heat enough water for several applications running at the same time. You can also install a single tankless water heater for the entire house, or separate ones for appliances that use more hot water.

Finding the proper size and type will depend on the flow rate—measured  by a GPM (gallons per minute) number—that each fixture needs. Every application has a standard flow rate that must be added up in order to calculate the hot water demands for your entire home. For instance, if someone is using a sink with a 1.5 GPM at the same time another person is running a shower with a 2.0 GPM, the flow rate for the tankless unit would need to be at least 3.5 gallons per minute. You will have to add up the flow rate for all the applications in the house to get the minimum GPM figure for your tankless water heater.

In addition to flow rates, tankless hot water heaters are also measured by how much the water temperature needs to rise as it moves through the heating unit. You can determine the temperature rise for each application by subtracting the temperature of water coming in from the desired temperature going out. Once you add those together with the overall flow rates, you will know which tankless water heater can handle your overall hot water needs.

Before you buy an on demand hot water heater, it is best to talk to a professional installer. While the flow rates and temperature rise for most household appliances are fairly standard, these numbers can vary because of several factors. Size is not the only factor to consider when shopping for a tankless water heater. Fuel type and efficiency should also be factored in to your purchase, which is another reason to talk to a professional.

If you aren’t sure what type or size of tankless water heater is right for your Hayden home, call Advantage Airtech Heating & Air Conditioning to speak with one of our professional installers. We are always glad to offer our expert advice so that you can meet all of your hot water needs in the most efficient way possible.

Tags: , , , ,
Posted in Water Heater | Comments Off

Heat Recovery Ventilator – What Is It and When Do You Need It in Uxbridge?

Monday, December 19th, 2011

While the design of modern homes is to retain as much energy as possible while minimizing the cost of heating and cooling, that very design can have a negative impact on your Uxbridge home’s indoor air quality. Because air cannot pass freely between indoor and outdoor environments, you are stuck breathing the same air day after day.

Luckily, there are options that will exchange the heat in your indoor air to the outdoor air as it enters your home. In effect, you can retain all of the heat your home produces each day before it leaves the house. It works equally well in the summer to retain the cooled air your air conditioning units produce.

How Heat Recovery Works

Heat recovery ventilators come in many forms, including simple ventilation, heat exchange, or air exchanging. There are even some indoor heat pumps that will carefully draw heat from the air as it’s removed from your home and recirculate it through your air ducts.

The idea is the same no matter how the system is installed. As air leaves your home through a ventilator, a counter-flow heat exchanger transfers energy between the air leaving and entering your home. So, instead of warm air leaving and cold air entering, the air coming into your home takes the heat from the air leaving your home. Air comes and goes, but heat stays inside.

In the summer, the same system works in reverse to remove heat from the air coming into your home and keep it outside. The one thing to keep in mind with a heat recovery ventilator is that it doesn’t retain the humidity in your home as an energy recovery ventilator would. If you live in an area with very high or very low humidity during summer or winter, an ERV may be a better solution for your needs.

Air Quality Benefits

The goal of a good heat recovery ventilator is not just to retain the heated or cooled air in your home. It is also to ensure you have clean, fresh air to breathe each day. Most people don’t realize, but when you don’t circulate your air and your home is sealed up with enhanced weather-stripping and high quality insulation, unwanted contaminants begin to build up. A heat recovery ventilator makes sure you not only get fresh air, but that it’s properly filtered and the heat or cooling your comfort system produces is retained. No money is lost, energy is saved, and your family stays comfortable and healthy – everyone wins.

Tags: , , , , ,
Posted in Indoor Air Quality | Comments Off

Why Fall Maintenance is Important for Your Heating System: A Tip From Caesarea

Friday, October 14th, 2011

When it comes to heating equipment maintenance and repairs for your Caesarea home, it does not pay to procrastinate. The longer you put off the maintenance, the higher the probability that your heating system will break down or your heating and cooling contractor will be unable to make an emergency repair when you need it. That’s why fall is the best time of the year to have maintenance and repair procedures performed.

Consider this: when do most people call a heating and cooling contractor? The answer: when they need a repair. The call could come in the middle of the night when a furnace stops working or during a family party on a weekend – both times when it is hard to find someone to do the repair work. Has this happened to you? If so, there are ways you could have prevented this from happening – and could have saved from cold nights and embarrassing situations with house guests.

You can avoid this aggravation and extra expense by scheduling fall maintenance for your heating system. Fall is often the “slow season” for heating and cooling professionals and many schedule their routine service and maintenance appointments during this time. Contractors expect to be busy during the peak winter months and prefer to spread out the workload as evenly as possible.

During fall maintenance, your heating equipment will be switched on and inspected. That may sound routine but by running your heating system early, you may be spared the expense of repairing your system when it fails to operate or run smoothly during the cold months. If there is a problem, it is better to fix it ahead of time.

There is no guarantee that a furnace that is tuned up in the fall will last throughout the winter without needing service. But a little preventive maintenance ahead of time will save a lot of heartache – and dollars – when a real emergency comes up.

Tags: , , , , , , , ,
Posted in Heating | Comments Off

Your HVAC System’s Condensate Drain Line: Some Pointers From Enniskillen

Friday, August 26th, 2011

There are a lot of components involved in a properly working HVAC system your Enniskillen home. One component that many people overlook is the drain line for the air conditioning system. Your air conditioning system has condenser coils that sweat the water drawn from the air in your home as it is cooled by your AC unit. These coils produce a significant volume of water, especially when it humidity is high, so a condensate drain pan is installed to capture the moisture and keep it from damaging your home.

A drain line from the drain pain out of your home is required to transfer all that extra water, but it can easily become clogged by debris in the area or simply from heavy condensation. If this happens, the drain line might need to be cleared or even replaced.

Inspecting your Condensate Drain Line

Full inspection of your drain line involves checking quite a few components, so I will point you to Inspectapedia for a thorough rundown of what you should look for (and some pictures to show you what you don’t want to see). But, in short, you want to look for evidence that your condensate drain is overflowing or that the liquid in your drain pan is backing up into the air handler.

You may also notice that there is no liquid coming out of the condenser – a sign that there may be a major problem in the system that needs immediate inspection. If this happens, make sure you check for blockages and if nothing is present, call a contractor.

Cleaning Your Drain Line

Each year, it is recommended that you clean your drain line to make sure it is clear and ready for the summer’s heavy cooling and high humidity. The simplest way to do this is to disconnect the drain line and attach a hose to blow the line clear. This can get a little messy, so make sure you dress for the occasion. Another option if you have a wet/dry vac is to attach the hose to the end of the drain line and suck free any moisture still in there. Most wet/dry systems have attachments for drain line clearing or you can order one.

If your drain line is not clearing properly or you think there may be structural damage suffered during the winter, call a professional for a more thorough inspection. If you have regular maintenance done on your AC system each spring, this should be part of the process so make sure you write down any questions you have for when the contractor visits your home.

Tags: , , , ,
Posted in Air Conditioning | Comments Off

Tips for Upgrading Your Hayden Central Air Conditioner

Friday, August 5th, 2011

When the time comes to upgrade your central air conditioner, if you live in Hayden or anywhere, you will have a lot of things to take into account. If you were generally satisfied with the performance of your old system, it can be very tempting to stick with a similar model. But if you do not examine all of the options out there right now, you may very well be missing out on a great deal.

If you already have a central air conditioner in place, chances are that you also have ductwork throughout your house. In that case, you will probably be better off with a packaged air conditioner as opposed to a split system. If it is a split system you are replacing, however, you should probably keep your search limited to other split systems. Installing a packaged air conditioner when you do not already have ducts in place can dramatically increase the overall cost of the project.

You will also want to make sure that the system you choose is compatible with the heating system and air handler that you already have in place. Most central air conditioning systems can be integrated easily with all types of heating systems, but you should still check to make sure this will not be a problem, particularly if you have an older heating system.

In terms of picking out the right new system for your home, energy efficiency is probably the main factor to consider. While just about every air conditioner on the market right now will be much more efficient than the unit you are replacing, you want to make sure you get a model that will provide you with the optimal savings in the long run.

This does not necessarily mean that you should go out and buy the most energy efficient air conditioner out there. In fact, because the more energy efficient units are also typically more expensive, you may not actually save money by going that route. But you will do well to choose a unit that will save you enough monthly to offset the installation costs and for most people, that means that you will want an air conditioner that is either a SEER 14 or SEER 16.

Of course, the actual amount of money you will save as you move up through the SEER rankings depends on how much you use your air conditioner to begin with. If you live somewhere with very hot weather and you use your unit for a large chunk of the year, it may very well be worth it for you to opt for a very high efficiency model.

Tags: , , , , ,
Posted in Air Conditioning | Comments Off

How Do I Find the Right Size Unit for My Room?

Wednesday, June 15th, 2011

When buying an air conditioner, there are a lot of things you need to take into account. One of the most important is the size and power of the unit you choose. Air conditioners come in many different sizes, so if you really want to get the most out of your purchase, you need to do your research and pick one that fits your home like a glove.

Square Feet and BTUs

The best way to determine how large of an air conditioner you need is to match the number of BTUs the unit has to the square footage of the room you want to use it in. That means you need to know what room you’re buying it for before you make your purchase.

The number of BTUs needed goes up proportionately with the room size, so even if you don’t have exact measurements or if your room is oddly shaped, you can get a good idea of how large an air conditioner you need. For instance, a 400 to 550 square foot room is best served by an air conditioner with between 8,000 and 11,000 BTUs, while a room that’s only 250 square feet would probably be fine with a 6,000 BTU unit.

Bigger Isn’t Always Better

One of the most common mistakes people make when buying an air conditioner is to assume that the bigger the unit the better it will work. The truth is that buying an air conditioner that’s too big for your room is just as much of a waste as buying one that’s too small.

A larger air conditioner will cost more, and it will probably make the room too cold. It will also cycle on and off more frequently than a properly sized unit and it won’t be able to properly control the humidity level, leaving you with a cold, damp environment. That’s not very comfortable.

Other Factors

The square footage is definitely the most important piece of data you’ll need before buying a new air conditioner for any room in your house. But don’t forget to take some other factors into account as well. For instance, if the room has particularly high ceilings or receives a lot of direct sunlight, you’ll probably need a slightly more powerful unit than the straight square footage would indicate.

If you’re not sure how certain features of your home will impact your buying decision, call a professional who can help you get a more exact idea of what it will take to stay cool.

Tags: , ,
Posted in Air Conditioning | Comments Off

What is the COP and Why Is It Important?

Friday, June 3rd, 2011

If you’ve been researching air conditioners, you’ve probably seen all sorts of numbers associated with each model. One of these numbers is the Coefficient of Performance (COP). While it’s good to gather as much data as you can before you make a purchasing decision, you also need to know what that data means if it’s going to help you make the best selection possible.

Measuring COP

Calculating the COP for any air conditioning model is relatively simple. The number you see displayed on the box is the ratio of energy input to cooling output. For the most part, the air conditioners you’re probably been looking at have a COP of between 2.5 and 4.0, although newer models are beginning to appear with COPs of up to 5.0.

The higher the COP, of course, the more efficient the air conditioner, so it makes sense to take this number into account when you’re making your purchase. You should also keep in mind, though, that the COP is not a constant measurement. The warmer it is outside, the lower your unit’s COP will be. However, this is standard across all units, so a relative COP comparison is still a viable evaluation method.

If you’re not sure what COP you should look for or whether a lower number will be effective for your home (especially if you only need to cool a small space), you should talk to a professional who can help you match the right COP level to your particular living space.

Improving Efficiency

While it’s always a good idea to get an air conditioner with the best energy efficiency ratings possible, that’s not the only thing you can do to reduce your energy usage and keep your cooling costs down. For instance, there are plenty of ways to keep your home naturally cooler without even turning on the air conditioner.

Even when you do need to flip it on, anything else you can do to reduce the indoor temperature will make it easier for your air conditioner to keep your house comfortable. So put up some awnings, run the ceiling fan and close the blinds to block out that harsh afternoon sun. The more you can do to reduce your indoor temperature naturally, the less your air conditioner will have to do, and the lower your cooling costs will be.

Tags:
Posted in Air Conditioning | Comments Off